Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network > Configure Your Machine for an Enterprise Wireless Network
• If you configure your machine using EAP-TLS authentication, you must install the client certificate issued by a CA before you start configuration. Contact your network administrator about the client certificate. If you have installed more than one certificate, we recommend writing down the certificate name you want to use.
• If you verify your machine using the common name of the server certificate, we recommend writing down the common name before you start configuration. Contact your network administrator about the common name of the server certificate.
2. Press a or b to select the [Network] option, and then press OK.
3. Press a or b to select the [WLAN] option, and then press OK.
4. Press a or b to select the [Setup Wizard] option, and then press OK.
5. When [WLAN Enable?] appears, press a to select On.
This will start the wireless setup wizard. To cancel, press Cancel.
6. The machine will search for your network and display a list of available SSIDs. Press a or b to select the [<New SSID>] option, and then press OK.
7. Enter the SSID name, and then press OK.
8. Press a or b to select the [Infrastructure] option, and then press OK.
9. Press a or b to select the Authentication Method you want, and then press OK.
10. Do one of the following:
• If you selected the [LEAP] option, enter the user ID, and then press OK.
Enter the Password, and then press OK.
• If you selected the [EAP-FAST], [PEAP] or [EAP-TTLS] option, press a or b to select the Inner Authentication Method [NONE], [CHAP], [MS-CHAP], [MS-CHAPv2], [PAP] or [GTC], and then press OK.
Depending on your Authentication Method, the Inner Authentication Method selections differ.
Press a or b to select the Encryption Type [TKIP + AES] or [AES], and then press OK.
Press a or b to select the Verification Method [No Verification], [CA] or [CA+Server ID], and then press OK.
- If you selected the [CA+Server ID] option, enter the server ID, user ID and password (if required), and then press OK for each option.
- For other selections, enter the user ID and the Password, and then press OK for each option.
If you have not imported a CA certificate into your machine, the machine will display the message [No Verification].
• If you selected the [EAP-TLS] option, press a or b to select the Encryption Type [TKIP + AES] or [AES], and then press OK.
When the machine displays a list of available Client Certificates, select the certificate you want.
Press a or b to select the Verification Method [No Verification], [CA] or [CA+Server ID], and then press OK.
- If you selected the [CA+Server ID] option, enter the server ID and user ID, and then press OK for each option.
- For other selections, enter the user ID, and then press OK.
If you have not imported a CA certificate into your machine, the machine will display the message [No Verification].
11. To apply the settings, press a. To cancel, press b.
12. The machine will attempt to connect to the wireless device you have selected.
If your wireless device is connected successfully, the machine's LCD displays [Connected].
You have completed the wireless network setup. To install drivers and software necessary for operating your device, insert the Brother Installation CD-ROM to your computer or go to your model's Downloads page on the Brother Solutions Center at support.brother.com to install drivers and software necessary for operating your device.
HL-L6400DW/HL-L6400DWT
Before configuring your machine, we recommend writing down your wireless network settings. You will need this information before you continue with the configuration.
1. Check and record the current wireless network settings.
Network Name (SSID)
Communication Mode
Authentication Method
Encryption Mode User ID Password
Infrastructure LEAP CKIP
EAP-FAST/NONE AES TKIP
EAP-FAST/MS-CHOPv2
AES TKIP
EAP-FAST/GTC AES
TKIP PEAP/MS-CHAPv2 AES
TKIP
PEAP/GTC AES
TKIP EAP-TTLS/CHAP AES
TKIP
EAP-TTLS/MS-CHAP
AES TKIP
EAP-TTLS/MS-CHAPv2
AES TKIP
EAP-TTLS/PAP AES
TKIP
EAP-TLS AES
-• If you configure your machine using EAP-TLS authentication, you must install the client certificate issued by a CA before you start configuration. Contact your network administrator about the client certificate. If you have installed more than one certificate, we recommend writing down the certificate name you want to use.
• If you verify your machine using the common name of the server certificate, we recommend writing down the common name before you start configuration. Contact your network administrator about the common name of the server certificate.
2. Press [Settings] > [Network] > [WLAN] > [Setup Wizard].
3. When [Switch network interface to wireless?] appears, press [Yes].
This will start the wireless setup wizard. To cancel, press [No].
4. The machine will search for your network and display a list of available SSIDs. Press a or b to display the [<New SSID>] option.
5. Press [<New SSID>].
6. Enter the SSID name, and then press [OK].
For more information about how to enter text, see the User's Guide.
7. Press [Infrastructure].
8. Press a or b to display the Authentication Method you want.
9. Press the Authentication Method you want.
10. Do one of the following:
• If you selected the [LEAP] option, enter the user ID, and then press [OK]. Enter the Password, and then press [OK].
• If you selected the [EAP-FAST], [PEAP] or [EAP-TTLS] option, press a or b to select the Inner Authentication Method [NONE], [CHAP], [MS-CHAP], [MS-CHAPv2], [GTC] or [PAP].
Depending on your Authentication Method, the Inner Authentication Method selections differ.
Press a or b to select the Encryption Type [TKIP+AES] or [AES].
Press a or b to select the Verification Method [No Verification], [CA] or [CA + Server ID].
- If you selected the [CA + Server ID] option, enter the server ID, user ID and password (if required), and then press [OK] for each option.
- For other selections, enter the user ID and Password, and then press [OK] for each option.
If you have not imported a CA certificate into your machine, the machine will display the message [No Verification].
• If you selected the [EAP-TLS] option, press a or b to select the Encryption Type [TKIP+AES] or [AES].
When the machine displays a list of available Client Certificates, select the certificate you want.
Press a or b to select the Verification Method [No Verification], [CA] or [CA + Server ID].
- If you selected the [CA + Server ID] option, enter the server ID and user ID, and then press [OK]
for each option.
- For other selections, enter the user ID, and then press [OK].
If you have not imported a CA certificate into your machine, the machine will display the message [No Verification].
11. To apply the settings, press [Yes]. To cancel, press [No].
12. The machine attempts to connect to the wireless device you have selected.
If your wireless device is connected successfully, the machine's LCD displays [Connected].
You have completed the wireless network setup. To install drivers and software necessary for operating your device, insert the Brother Installation CD-ROM to your computer or go to your model's Downloads page on the Brother Solutions Center at support.brother.com to install drivers and software necessary for operating your device.
Related Information
• Additional Methods of Configuring Your Brother Machine for a Wireless Network
• Wireless LAN Report Error Codes
Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network > Use Wi-Fi Direct®