GRUNDFOS Scheda Tecnica
MSS.11.1.2 1x230V
Pompa Grundfos 97901037
Grazie per l’interesse nei nostri prodotti. Potete contattarci direttamente per ulteriori informazioni o visitare il nostro sito web:
https://www.lenntech.it/grundfos/MULSING/97901037/MSS-11-1-2.html info@lenntech.com
tel. +31 152 755 706
fax. +31 152 616 289
Posizione Q.tà Descrizione 1 MSS.11.1.2
Attenzione: le foto e i disegni sono solo indicativi
Codice prodotto: A richiesta
Supplied as complete unit ready for installation, the Multilift consist of a fully integrated collecting tank with pump and submersible motor, non-return valve, discharge adapter with flexible connection piece DN100 mounted on the collecting tank and a pre-wired Controller incl. a level sensor.
The fully integrated collecting tank has all necessary ports for the connection of inlet pipe in heights of 180mm and 250mm, vent pipe DN50 and a manually operated diaphragm pump (accessory).
The collecting tank contains 7 inlet sockets
around it's shape. Back inlets 2x DN100 with one socket seal, socket for inlet at the sides 2 x DN100, top inlet DN100. 2x DN50 on top and side.
Multilift corrosion free polyethylen collecting tanks are gas- and odour-proof as well as watertight , reduction of residual water and less sedimentation by chamfered bottom design.
The pump with Vortex impeller and a maintenance free submersible motor, oil chamber with
physiological harmless oil filling between two shaft seals. Motor protection via motor-protective circuit breaker inside pump head.
LC220 controller with microprocessor is equipped with LED for all monitoring necessities. The pump and sensor are connected to the controller with 4m or 10m cable and tube length. The power supply cable is 1,5m with plug (incl. phase inverter for 3 phase motor)
Contactless, piezo resistive pressure sensor pluggable inside the cabinet, monitored by controller.
Blockage free pressure tube inside the tank without movable parts inside wastewater.
The controller offer monitoring of pump operation.
Controller functions:
• on/off control of one wastewater pump based on a continuous signal from a piezo-resistive sensor
• dry running motor protection via run-time limitation with a following emergency operation
• 24h automatic test runs during long periods of inactivity
• operating indication:
- pump status (running, fault)
- time for service/maintenance once a year (selectable on/off by DIP switch)
• fault indication:
- phase-sequence fault and missing phase at 3ph. motors - high-water alarm
- sensor fault
- external alarm-switch (only alarm) - potential free contact for common alarm
• automatic or manual alarm resetting (selectable by DIP switch)
• easy selection of start level 180 or 250mm (selectable by DIP switch)
One additional input to connect a separate level switch to be used for flood detection outside the Multilift (external alarm). Lifting stations are often installed in a sump inside the basement at the lowest point in the building. In case of e.g. groundwater inflow or water pipe burst, an alarm will be indicated by the controller.
The Multilift range is designed due to the standard EN12050-1, approved and monitored by external institute LGA. Further approvals are VDE, GHOST, CB, EMV
Tecnico:
Tipo di girante: VORTEX
Dimensione max delle particelle: 40 mm CE approved (Yes/No): Y EN number for LGA approval: Y
Tipo di valvola: Valv clap.
Materiali:
Corpo pompa: Composite
Serbatoio: LDPE
Guarnizione: NBR
Liquido:
Temp. liquido max: 40 °C
Densità: 998.2 kg/m³
Dati elettrici:
Potenza assorbita - P1: 1.7 kW
Potenza - P2: 1.1 kW
Frequenza di rete: 50 Hz
Voltaggio: 1 x 230 V
Toller. voltaggio: +10/-6 % Max. numero avviamenti per ora: 60
Corrente: 8 A
Cos phi - fattore di potenza: 0.95 Velocità nominale: 2760 rpm
Nr di poli: 2
Tipo di avviamento: DOL
Classe di protezione (IEC 34-5): IP68 Classe di isolamento (IEC 85 ): F Tipo di spina del cavo: SCHUKO Cavo di alimentazione: 1.5 m Serbatoio:
Volume totale del serbatoio(i): 44 l
Volume effettivo del serbatoio con ingresso 180 mm: 20 l Volume effettivo del serbatoio con ingresso 250 mm: 28 l
A richiesta MSS.11.1.2 50 Hz
H [m]
0 1 2 3 4 5 6 7 8 9 10 11 12
Q [l/s]
0 1 2 3 4 5 6 7 8 9
eta [%]
0 5 10 15 20 25 30 35 40 45 MSS.11.1.2, 50Hz
P1 [kW]
0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8
H [m]
0 1 2 3 4 5 6 7 8 9 10 11 12
Q [l/s]
0 1 2 3 4 5 6 7 8 9
eta [%]
0 5 10 15 20 25 30 35 40 45 MSS.11.1.2, 50Hz
P1 [kW]
0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6
522
510 110 DN100 /
DN80 75
70
140
55 61 216
125 460
196
185
111
50
DN50 / DN50 / 52
110 DN100 /
110 DN100 /
180 250
110 DN100 /
180
115 460 383 340
195
50
50 DN50 / 110
DN100 / 52 DN50 /
120
250
115
353
50 DN50 /
L1 L2 L3 N PE PE N U1 V1 W1
L N PE PE L
BNBU GNYE
Protector N
Descrizione Valore
Informazioni generali:
Nome prodotto: MSS.11.1.2
Codice prodotto: A richiesta
Codice EAN: A richiesta
Tecnico:
Portata massima: 8.61 l/s
Prevalenza max: 10.4 m
Tipo di girante: VORTEX
Dimensione max delle particelle: 40 mm
CE approved (Yes/No): Y
EN number for LGA approval: Y
Tipo di valvola: Valv clap.
Materiali:
Corpo pompa: Composite
Serbatoio: LDPE
Guarnizione: NBR
Liquido:
Temp. liquido max: 40 °C
Densità: 998.2 kg/m³
Dati elettrici:
Potenza assorbita - P1: 1.7 kW
Potenza - P2: 1.1 kW
Frequenza di rete: 50 Hz
Voltaggio: 1 x 230 V
Toller. voltaggio: +10/-6 %
Max. numero avviamenti per ora: 60
Corrente: 8 A
Cos phi - fattore di potenza: 0.95
Velocità nominale: 2760 rpm
Nr di poli: 2
Tipo di avviamento: DOL
Classe di protezione (IEC 34-5): IP68 Classe di isolamento (IEC 85 ): F
Protezione motore: KLIXON
Cavo motore: 4 m
Tipo di cavo: H07RN-F
Tipo di spina del cavo: SCHUKO
Cavo di alimentazione: 1.5 m
Antideflagrante: H05VV-F
Controlli:
Modi di funzionamento: S3-10%, 1 MIN.
Serbatoio:
Volume totale del serbatoio(i): 44 l Volume effettivo del serbatoio con ingresso 180 mm:
20 l
Volume effettivo del serbatoio con ingresso
250 mm: 28 l
510110DN100 /DN80755512546018550DN50 /52DN50 /
110DN100 /110DN100 /
110DN100 /11519550DN50 /110DN100 /52DN50 /11550DN50 /
A richiesta MSS.11.1.2 50 Hz
522
510 110
DN100 /
DN80 75
70
140
55
61 216
125 460
196
185
111
50
DN50 / DN50 / 52
110 DN100 /
110 DN100 /
180 250
110 DN100 /
180
115
460 383 340
195
50
50 DN50 / 110
DN100 / 52 DN50 /
120
250
115
353
50 DN50 /
Vista esplosa
301a 219
92 7
7a 77
301a
92
11 9 51
100 49 105
45
215a 215
18
215a 217
534a 534531
531a 28
17
251d 251a
6 11b
66a 67
530 530a
Disegno in sezione (TM058200 for TPE2,TPE3)
4
2 1
3
5
Vista esplosa ( TM057026 for MGE model H/I )
251d
251b
290
287
277a
286
277
273a
273
268 268a 289a 289
288b288 288a 251a
252b
156c 156b
156d 188
275a
153
154
158
178 185
192 191 159e
156c 156
151 152 266
187
291
293
252a
172
150 287a
502
273b
157
Nota: Le informazioni riguardanti le pompe Grundfos nel documento presente potrebbe essere superate.
I dati contenuti possono subire variazioni senza preavviso.
Siete pregati di contattarci per verificare che le informazioni e dati di cui sopra siano validi/aggiornati.
Tutte le informazioni sono Grundfos Copyright, tutti i diritti riservati.
info@lenntech.com https://www.lenntech.it tel. +31 152 755 706 fax. +31 152 616 289