electronic (Reg. Metered-Time) 8-10-12-15-20-25-30 lt. resin
Variants
Code Description
15000105-08 Automatic water softener valve AUTOTROL 255/760 Logix 1" electronic (Reg. Metered-time) 8 lt. Europe I 15000105-10 Automatic water softener valve AUTOTROL 255/760 Logix 1" electronic (Reg. Metered-time) 10 lt. Europe I 15000105-12 Automatic water softener valve AUTOTROL 255/760 Logix 1" electronic (Reg. Metered-time) 12 lt. Luxury I 15000105-15 Automatic water softener valve AUTOTROL 255/760 Logix 1" electronic (Reg. Metered-time) 15 lt. Europe II 15000105-20 Automatic water softener valve AUTOTROL 255/760 Logix 1" electronic (Reg. Metered-time) 20 lt. Europe II 15000105-25 Automatic water softener valve AUTOTROL 255/760 Logix 1" electronic (Reg. Metered-time) 25 lt. Europe II 15000105-30 Automatic water softener valve AUTOTROL 255/760 Logix 1" electronic (Reg. Metered-time) 30 lt. Luxury II
Automatic water softener. Electronic AUTOTROL valve 255/760 Logix 1" (Reg. Metered-time). Valve body made of Noryl plastic material, NSF listed. Programming is simple and fast, just enter the time, day of week, time of regeneration, typically 02.00 at night, number of days between regenerations and hardness input. Complete with plug adapter 12/230V - 50Hz European plug. Hardness regulator output. Clutching the set screw is going to open the clapper by-pass, which allow you to mix raw water with water treated by device. At the first turn of the screw, the water hardness output increases. Is required output minimum hardness of around 15°F, but the most commonly used setting is not less than 5°F. Loosening setting screw will allow the clapper by-pass to close. The closing action will reduce mixing with raw water output.
To mix a specific output hardness value, adjust screw and test water. Repeat the procedure until you reach the desired hardness value. To check input/output hardness from the device, we recommend to buy cod.
13000001 Titrant kit total hardness (1°F) 15cc single reagent.
TO BUY WITH EVERY SOFTENER
1x 15010101-018 Chlorine generator kit for Autotrol valve 255
1x 02001014 3-pieces standard housing 10" clear IN-OUT 1" with wrench & wall mounting bracket.
2x 04001006-05 Ionicore wound polypropylene cartridge 9-3/4'' - 50 micron (50) 1x Kit 13000001 Titrant total hardness (1 ° F) 15cc single reagent.
* Water softeners are supplied without salt, we recommend to use pads salt.
The device is supplied with chlorine producer assembled ( if ordered ) and programmed with a input hardness of 40°F, hardness of 0°F output and a safety regeneration every 7 days.
A bypass valve system must be installed on all systems. The bypass valves isolate the device from the water system and allow the use of untreated water. Routine maintenance or service may also require that the system is put in bypass.
Benefits and advantages
Reduction of water hardness, which is cause of scale. ENERGY SAVING: the device prevents the formation of deposits in pipes and hydraulic lines. Greater sense of wellness during the shower. Skin soft and clean. Increased duration of appliances and boilers. COST SAVING: reduction in the use of soaps, fabric softeners and chemicals. Reduced maintenance costs. Fully automatic operation. It should just worry about adding salt in the water softner.
Increased sodium (for drinking water)
Most of the sodium consumed is taken with foods, especially ones obtained with industrial processing. Salt is a great preservative and therefore is used as an additive for processed products. The assumption of sodium with the water we drink is relatively low compared to that which is taken with food. All softeners to produce softened water through ion exchange resins in, produce softened water output sodium ions. The recommended sodium limit for water intended for human consumption is 200ppm liter. Depending on the concentration of sodium and water hardness, it is possible that the water presents a sodium concentration of higher than recommended. Where this is the case or if you need to follow a low salt content, it is advisable to install a reverse osmosis home for water to drink.
Features
* Min. pressure : 1.38 bar (1.38 kg/cm2)
* Max. pressure : 8.27 bar (8.27 kg/cm2)
* Minimum temperature: 2°C
* Maximum temperature: 38°C
* Input / Output water 1" female thread
* Exhaust: hose connector with 2m. of tube
* Overflow: hose connection 3/8"
Model Specifications 15000105-08 8lt. resin. (for 1/2 people)
* Exchange capacity: 44ºHFxm3.
* Salt consumption for regeneration: 1,24 Kg./salt.
* Water consumption for regeneration: 53,6lt.
* Quantity of water treated for regeneration, 30°F-0,68m3, 35°F-1,26m3, 40°F-1,1m3, 45°F-0,98m3, 50°F-0,88m3, 60°F-0,73m3.
* Max. flow 0,32 m3/h
* Dimensions Europe I - Base (mm): 480x320 * Height (mm): 655 Model Specifications 15000105-10 10lt. resin. (for 2/3 people)
* Exchange capacity: 55ºHFxm3.
* Salt consumption for regeneration: 1,8 Kg./salt.
* Water consumption for regeneration: 67lt.
* Quantity of treated water for regeneration, 30°F-1,83m3, 35°F-1,57m3, 40°F-1,37m3, 45°F-1,22m3, 50°F-1,1m3, 60°F-0,916m3.
* Max. flow 0,54m3/h
* Dimensions Europe I - Base (mm): 480x320 * Height (mm): 655 Model Specifications 15000105-12 12lt. resin. (for 2/3 people)
* Exchange capacity: 66ºHFxm3.
* Salt consumption for regeneration: 1,8 Kg./salt.
* Water consumption for regeneration: 80,4lt.
* Quantity of treated water for regeneration, 30°F-2,2m3, 35°F-1,88m3, 40°F-1,65m3, 45°F-1,46m3, 50°F-1,32m3, 60°F-1,1m3.
* Max. flow 0,54m3/h
* Dimensions Luxury I - Base (mm): 605x350 * Height (mm): 670 Model Specifications 15000105-15 15lt. resin. (for 3/4 people)
* Exchange capacity: 90ºHFxm3.
* Salt consumption for regeneration: 2,5 Kg./salt.
* Water consumption for regeneration: 100,5lt.
* Quantity of water treated for regeneration, 30°F-3,00m3, 35°F-2,57m3, 40°F-2,25m3, 45°F-2,00m3, 50°F-1,8m3, 60°F-1,5m3.
* Max. flow 0,68m3/h
* Dimensions Europe II - Base (mm): 480x320 * Height (mm): 1.120 Model Specifications 15000105-20 20lt. resin. ( for 4/6 People)
* Exchange capacity: 110ºHFxm3.
* Salt consumption for regeneration: 3,2 Kg./salt.
* Water consumption for regeneration: 134lt.
* Quantity of water treated for regeneration, 30°F-3,66m3, 35°F-3,14m3, 40°F-2,75m3, 45°F-2,44m3, 50°F-2,2m3, 60°F-1,83m3.
* Max. flow 0,942m3/h
* Dimensions Europe II - Base (mm): 480x320 * Height (mm): 1.120 Model Specifications 15000105-25 25lt. resin. (for 6/8 People)
* Exchange capacity: 137ºHFxm3.
* Salt consumption for regeneration: 3,9 Kg./salt.
* Water consumption for regeneration: 167,5lt.
* Quantity of water treated for regeneration, 30°F-4,56m3, 35°F-3,14m3, 40°F-3,91m3, 45°F-3,04m3, 50°F-2,74m3, 60°F-2,28m3.
* Max. flow 1m3/h
* Dimensions Europe II - Base (mm): 480x320 * Height (mm): 1.120 Model Specifications 15000105-30 30lt. resin. (for 6/8/10 People)
* Exchange capacity: 160ºHFxm3.
* Salt consumption for regeneration: 4,3 Kg./salt.
* Water consumption for regeneration: 201lt.
* Quantity of water treated for regeneration, 30°F-5,33m3, 35°F-4,5m3, 40°F-4m3, 45°F-3,55m3, 50°F-3,2m3, 60°F-2,66m3.
* Max. flow 1,47m3/h
* Dimensions Luxury II - Base (mm): 605x350 * Height (mm): 1.120 Code: 15000107
Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 8-10-12-15-20-25-30 lt. resin
Variants
Code Description
15000107-08 Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 8 lt. Europe I 15000107-10 Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 10 lt. Europe I 15000107-12 Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 12 lt. Luxury I 15000107-15 Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 15 lt. Europe II
15000107-20 Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 20 lt. Europe II 15000107-25 Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 25 lt. Europe II 15000107-30 Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 30 lt. Luxury II
FLECK 5600 SXT Electronic valve Automatic meter/time regeneration . Program with high performance which allows a low water and salt per regeneration consumption. Valve body made of Noryl plastic material, NSF listed. Programming is simple and fast, just enter time, day of week, time of regeneration, typically 02.00 at night, number of days between regenerations and hardness input. Complete with plug adapter 12/230V - 50Hz European plug. Hardness regulator output. Is raccomended a minimum hardness in output of around 15 °F , but most commonly used setting is not less than 5 ° F. Loosening setting screw will allow clapper by-pass to close. The closing action will reduce mixing with raw water output. To mix a specific output hardness value, adjust screw and test water. Repeat procedure until you reach desired hardness value. To check input/output hardness from device, we recommend to buy cod. 13000001 Titrant kit total hardness (1°F) 15cc single reagent.
TO BUY WITH EVERY SOFTENER
1x 15000407 Chlorine generator complete with fittings
1x 02001014 3-pieces standard housing 10" clear IN-OUT 1" with wrench & wall mounting bracket.
2x 04001006-05 Ionicore wound polypropylene cartridge 9-3/4'' - 50 micron (50) 1x Kit 13000001 Titrant total hardness (1 ° F) 15cc single reagent.
* Water softeners are supplied without salt, we recommend to use pads salt.
The device is supplied with chlorine producer assembled and programmed with a input hardness of 40°F, hardness of 0°F output and a safety regeneration every 7 days.The bypass valves isolate device from water system and allow the use of untreated water. Routine maintenance or service may also require that system is put in bypass.
What are the benefits that SXT Controller offer?
* Simple and intuitive programming
* Large LCD display with blue backlight
* 48 hours of internal power backup
* Real time of day in hours and minutes
* Residual volume of softened water
* Display of cycle regeneration phases and remaining time
* Service and self-diagnosis indicators
* Fast and easy capacity, time and day of regeneration configuration
* Advanced programming options, including ability to program up to 6 cycles of regeneration with independent adjustment of time
* The program setting will not be lost in case of power outages remaining in memory
* Electronic regeneration step-by-step
* Manually, delayed or immediate regeneration Benefits and advantages
Reduction of water hardness, which is cause of scale. ENERGY SAVING: the device prevents formation of deposits in pipes and hydraulic lines. Greater sense of wellness during shower. Skin soft and clean.
Increased duration of appliances and boilers. COST SAVING: reduction in use of soaps, fabric softeners and chemicals. Reduced maintenance costs. Fully automatic operation. It should just worry about adding salt in water softner.
Increased sodium (for drinking water)
Most of the sodium consumed is taken with foods, especially ones obtained with industrial processing. Salt is a great preservative and therefore is used as an additive for processed products. The assumption of sodium with the water we drink is relatively low compared to that which is taken with food. All softeners to produce softened water through ion exchange resins in, produce softened water output sodium ions. The recommended sodium limit for water intended for human consumption is 200ppm liter. Depending on sodium concentration and water hardness, it is possible that water presents an higher sodium concentration than recommended. Where this is the case or if you need to follow a low salt content, it is advisable to install a domestic reverse osmosis for drinking water.
Specifications
* Min. pressure: 1.4 bar (1.4 kg/cm2)
* Max. pressure: 8.5 bar (8.5 kg/cm2)
* Min. temperature: 2 ° C
* Max. temperature: 43 ° C
* Input/Output water 1" female thread
* Exhaust: hose connector with 2m. of tube
* Overflow: hose connection 3/8"
Model Specifications 15000107-08 8lt. resin (for 1/2 people)
* Exchange capacity: 38.56 º HFxm3.
* Salt consumption for regeneration: 0.88 Kg./Salt.
* Water consumption for regeneration: 47,2lt.
* Quantity of treated water for regeneration, 30°F-1,28m3, 35°F-1,10m3, 40°F-0,96m3, 45°F-0,85m3, 50°F-0,77m3, 60°F-0,64M3.
* Max. flow: 0.36 m3/h
* Dimensions Europe I - Base (mm): 480x320 * Height (mm): 655 Model Specifications 15000107-10 10lt. resin (for 1/2 people)
* Exchange capacity: 48,20ºHFxm3.
* Salt consumption for regeneration: 1,10 Kg./salt.
* Water consumption for regeneration: 63,8lt.
* Quantity of treated water for regeneration, 30°F-1,6m3, 35°F-1,38m3, 40°F-1,21m3, 45°F-1,07m3, 50°F-0,97m3, 60°F-0,80m3.
* Max. flow: 0,45m3/h
* Dimensions Europe I - Base (mm): 480x320 * Height (mm): 655 Model Specifications 15000107-12 12lt. resin (for 2/3 people)
* Exchange capacity: 57,84ºHFxm3.
* Salt consumption for regeneration: 1,32 Kg./salt.
* Water consumption for regeneration: 70,8lt.
* Quantity of treated water for regeneration, 30°F-1,93m3, 35°F-1,65m3, 40°F-1,44m3, 45°F-1,29m3, 50°F-1,16m3, 60°F-0,96m3.
* Max. flow: 0,54m3/h
* Dimensions Luxury I - Base (mm): 605x350 * Height (mm): 670 Model Specifications 15000107-15 15lt. resin (for 3/4 people)
* Exchange capacity: 72,30ºHFxm3.
* Salt consumption for regeneration: 1,65 Kg./salt.
* Water consumption for regeneration: 90,7lt.
* Quantity of treated water for regeneration, 30°F-2,41m3, 35°F-2,06m3, 40°F-1,80m3, 45°F-1,60m3, 50°F-1,45m3, 60°F-1,20m3.
* Max. flow: 0,67m3/h
* Dimensions Europe II - Base (mm): 480x320 * Height (mm): 1.120 Model Specifications 15000107-20 20lt. resin (for 4/6 people)
* Exchange capacity: 96,40ºHFxm3.
* Salt consumption for regeneration: 2,2 Kg./salt.
* Water consumption for regeneration: 124,1lt.
* Quantity of treated water for regeneration, 30°F-3,21m3, 35°F-2,75m3, 40°F-2,41m3, 45°F-2,14m3, 50°F-1,93m3, 60°F-1,60m3.
* Max. flow: 0,9m3/h
* Dimensions Europe II - Base (mm): 480x320 * Height (mm): 1.120 Model Specifications 15000107-25 25lt. resin (for 6/8 people)
* Exchange capacity: 120,50ºHFxm3.
* Salt consumption for regeneration: 2,75 Kg./salt.
* Water consumption for regeneration: 150lt.
* Quantity of treated water for regeneration, 30°F-4,01m3, 35°F-3,44m3, 40°F-3,01m3, 45°F-2,67m3, 50°F-2,41m3, 60°F-2,00m3.
* Max. flow: 1,12m3/h
* Dimensions Europe II - Base (mm): 480x320 * Height (mm): 1.120 Model Specifications 15000107-30 30lt. resin (for 6/8/10 people)
* Exchange capacity: 144,60ºHFxm3.
* Salt consumption for regeneration: 3,30 Kg./salt.
* Water consumption for regeneration: 179,7lt.
* Quantity of treated water for regeneration, 30°F-4,82m3, 35°F-4,13m3, 40°F-3,61m3, 45°F-3,21m3, 50°F-2,89m3, 60°F-2,41m3.
* Max. flow: 1,35m3/h
* Dimensions Luxury II - Base (mm): 605x350 * Height (mm): 1.120 Code: 15000116