Be sure that you or your installer follow these instructions closely so that your new dishwasher works properly and that you’re not at risk of injury when washing dishes.
New installation
If the dishwasher is a new installation, most of the installation work must be done before the dishwasher is moved into place.
Replacement
If the dishwasher is replacing an old dishwasher, you must check the exising dishwasher connections for compatibility with the new dishwasher. Replace the existing connections as necessary.
STEP 1. SELECTING THE BEST LOCATION FOR THE DISHWASHER
The installation position of dishwasher should be near the existing inlet and drain hoses and power cord.
One side of the cabinet sink should be chosen to facilitate the connection of drain hoses of the dishwasher.
1. Choose a place near the sink to facilitate the installation of inlet and drain hoses.
2. Less than 5 mm between the top of dishwasher and cabinet and the outer door aligned to cabinet.
Cabinet dimensions (unit: mm)
600
550 598
670~800
580
100 100
53
088~028 578~718 568~518 5050
DW60M5070IB_ET_DD81-02615K-00_EN.indd 34
DW60M5070IB_ET_DD81-02615K-00_EN.indd 34 2019-09-17 2:50:442019-09-17 2:50:44
Installing your dishwasher_35
07 INSTALLING YOUR DISHWASHER
3. If dishwasher is installed at the corner of the cabinet, there should be some space when the door is opened.
cabinet Dishwasher
Dishwasher
Door of Door of Dishwasher Dishwasher
Minimum space of 50 mm
Depending on where your electrical outlet is, you may need to cut a hole in the opposite cabinet side.
STEP 2. CHECKING WATER SUPPLY AND ELECTRICAL REQUIREMENTS
• The water supply line pressure must be between 0.04-1.0 MPa.
• Supply cold water only. Make sure that the water temperature does not exceed 60 ˚C.
• Do not supply hot water. Otherwise, the product may malfunction.
• Use a rated power of 220-240 V~, 50 Hz.
• Install the product while the power cord is unplugged.
• Use a power outlet with a maximum allowable current of 16 A. (The maximum current for this dish washer is 11 A.)
• When powering the dishwasher, ensure that your power supply has:
- An 220-240 V~, 50 Hz fuse or circuit breaker.
- An individual branch circuit serving your dishwasher.
• After the installation, check if the power cord is not bent or damaged.
• Ensure that the water supply valve is turned off before connecting the water supply line to the dishwasher.
• Seal the water supply line connections using teflon tape or sealing compound to stop any water leakage.
CAUTION
WARNING
DW60M5070IB_ET_DD81-02615K-00_EN.indd 35
DW60M5070IB_ET_DD81-02615K-00_EN.indd 35 2019-09-17 2:50:442019-09-17 2:50:44
36_Installing your dishwasher
STEP 3. PREPARING THE CUSTOM PANEL
This dishwasher model is equipped with an auto-balancing system in the door. It has a sliding hinge, which is perfect for plinth-less kitchens or for installation above a small cupboard. Custom panel’s height (A) can be between minimum 670 mm to maximum 800 mm depending on the installation environment. Custom panel’s weight must not exceed 10 kg. Refer to the table for the height (C) in relation to the cabinet’s height (B), and then determine the height of the custom panel.
A A
596 mm 596 mm
B B
C
C Min. 20Min. 20
A B C
670-800 mm
820 mm 20-150 mm
850 mm 50-180 mm
880 mm 80-210 mm
1. Put the installation template on the back of the custom panel and fi x it temporarily using transparent tape. Note that the rear of the custom panel will be attached to the dishwasher door.
2. Mark 4 points guided on the installation template.
3. Remove the installation template and tighten the Custom panel fi xers as shown.
7
1
1
1 1 6
5
5
10 6
Installing your dishwasher
DW60M5070IB_ET_DD81-02615K-00_EN.indd 36
DW60M5070IB_ET_DD81-02615K-00_EN.indd 36 2019-09-17 2:50:452019-09-17 2:50:45
Installing your dishwasher_37
07 INSTALLING YOUR DISHWASHER
4. While holding the custom panel, attach it to the door and insert the Custom panel fi xers into the corresponding holes at the door.
Use a custom panel between 4~10Kg.
Make sure the skirting board does not interfere with the dishwasher’s door fully opening and closing.
12 15
DW60M5070IB_ET_DD81-02615K-00_EN.indd 37
DW60M5070IB_ET_DD81-02615K-00_EN.indd 37 2019-09-17 2:50:452019-09-17 2:50:45
38_Installing your dishwasher
STEP 4. DISHWASHER INSTALLATION
1. Install the furniture door to the outer door of the dishwasher using the brackets provided. Refer to the template for positioning of the brackets.
2. Connect the inlet hose to the cold water supply.
3. Connect the drain hose. Refer to diagram.
4. Connect the power cord.
5. Affi x the condensation strip under the work surface of cabinet. Please ensure the condensation strip is fl ush with edge of work surface.
6. Place the dishwasher into position.
7. Level the dishwasher. The rear food can be adjusted from the front of the dishwasher by turning the Allen screw in the middle of the base of dishwasher use an Allen key. To adjust the front feet, use a fl at screw driver and turn the front feet until the dishwasher is level.
8. The dishwasher must be secured in place. There are two ways to do this:
A. Normal work surface : Put the installation hook into the slot of the side plane and se cure it to the work surface with the wood screws.
B. Marble or granite work top : Fix the side with Screw.
Installing your dishwasher
DW60M5070IB_ET_DD81-02615K-00_EN.indd 38
DW60M5070IB_ET_DD81-02615K-00_EN.indd 38 2019-09-17 2:50:452019-09-17 2:50:45
Installing your dishwasher_39
07 INSTALLING YOUR DISHWASHER
STEP 5. LEVELLING THE DISHWASHER
Check level front to back
Check level side to side
ƸťUĮǮĘ
Ƹť UĮǮĘ
Dishwasher must be level for proper dish rack operation and wash performance.
1. Place a spirit level on door and rack track inside the tub as shown to check that the dishwasher is level.
2. Level the dishwasher by adjusting the three levelling legs individually.
3. When level the dishwasher, please pay attention not to let the dishwasher tip over.
If the height of the leg is not high enough, use extra feet.
DW60M5070IB_ET_DD81-02615K-00_EN.indd 39
DW60M5070IB_ET_DD81-02615K-00_EN.indd 39 2019-09-17 2:50:462019-09-17 2:50:46
40_Troubleshooting