Bibliografia
Bibliografia
[1] ANSI/AGMA 2005-C96 [2] ANSI/AGMA 1010-E95
[3] Dudley’s gear handbook seconda edizione [4] R.Drago Fundamentals of gearing
[5] Esercitazione di Costruzione di Macchine “Modifica della sezione di prova del banco Renk al fine di testare ingranaggi conici” S.Palmeri, docente Prof. Ing. E. Manfredi [6] Guida alla sicurezza delle macchine – Arcidiacono, Citti, Mazzeranghi, Spinelli [7] Surface durability pitting formulas for bevel gear teeth - Gleason machine division [8] Pitting fatigue of gears-some ideas on appearance, mechanism and lubricant influence –
Bartz and Kruger
[9] Scoring resistance of bevel gear teeth – Gleason works
[10] Relazione intermedia del WP 140 del contratto di ricerca “caratterizzazione ed ottimizzazione delle attività di progettazione degli ingranaggi cilindrici e conici” – Ing. M.Gabiccini
[11] Analisi dei contatti di ingranamento di coppie coniche spirali ed ipoidi sotto carico – Ing. F. Pederneschi
[12] Meshing of a spiral bevel gear set with 3d finite element analysis – G.D. Bibel, R. Handshuh
[13] Contact stress analysis of spiral bevel gears using finite element analysis – G.D. Bibel, A. Kumar, S. Reddy
[14] Understanding tooth contact analysis – Gleason machine division
[16] Evaluation of gear stresses by finite element method – I. H. Filiz, O. Eyercioglu [17] prevent gear tooth scoring – machine design march 1980
[18] Experimental and analytical study of aerospace spiral bevel gear tooth fillet stresses –Q.Y. jiang, G.C. Barber
[19] Effect of different treatments and coatings on the scuffing performance of hardened steel discs al very high sliding speeds – Alanou, Evans, Snidle
[20] Condiction for scuffing failure of ground and superfinished steel disks at high sliding speeds using a gas turbine engine oil – Patching, Kweh, Evans, Snidle
Bibliografia
[22] A theoretical study of the effect of pinion offset on the dynamics of hypoid geared rotor system – Lim, Cheng
[23] Computerized simulation of transmission errors and shift of bearing contact for face milled hypoid gear drive – Litvin Chen, Sep, Wang
[24] Straight bevel gear design – Gleason machine division
[25] Formulas for revacycle bevel gear blank dimensions and static bending stresses – Gleason works
[26] A new perspective on the strength of bevel gear teeth – Gleason works
[27] Calcolo della temperatura di contatto per la verifica a scoring di ingranaggi con generiche curvature e velocità relative – F. Cumbo
[28] Bending stresses in bevel gear teeth – Gleason machine division [29] Hypoid face milled user’s manual – Ansol
[30] Elementi di macchine, vol 1,2,3 – Niemann, Winter
[31] Fondamenti della progettazione delle componenti delle macchine – Juvinall, Marshek [32] Guida alla sicurezza delle macchine – Arcidiacono, Citti, Mazzeranghi, Spinelli [33] Testing and inspecting bevel and hypoid gears – Gleason
[34] Lezioni di disegno di macchine – S.Barsali, G.C. Barsotti, U.Rosa
[35] La resistenza di ruote dentate coniche ad assi concorrenti – T. Omachi, K. Mitome
[36] Analysis of the effects of surface pitting and wear on the vibration of a gear transmission system – Choy, Polyschchuk, Zakrajsek, Handschuh, Townsend
[37] Testing of face-milled spiral bevel gears at hight-speed and load – R. Handschuh
[38] Transmission diagnostic research at NASA Lewis research center – Zakrajsek, Handschuh, Townsend, Lewicki, Decker
[39] Spiral bevel gear damage detection using decision fusion analysis – Dempsey, Handschuh, Afjeh
[40] Tesi di Laurea “Studio teorico e sperimentale del danneggiamento di dentature per impieghi aerospaziali, con particolare riferimento al micropitting” di Gianni Ferioli, relatore Prof. E. Manfredi