FILLING THE WATER TANK DURING USE Always check the water level in the tank
WKH XVH RI QRQ-FRQIRUPLQJ SURGXFWV GXH WR WKH SUHVHQFH RI FKHPLFDO DGGLWLYHV
EN
Enter the “Maintenance” menu (from the home page, “Guide and Setting”) to display and start the descaling cycle of the appliance.
When a message demanding descaling appears on the display, a descaling cycle must be carried out.
Start the “Descaling cycle” from the display and follow the instructions given on the display.
Slowly turn the ¿lter holder from right to left to remove it so as to avoid splashing water or coffee (Fig. ).
Remove the water softener ¿lter from the water tank.
Fill the water tank with fresh water up to the MAX level (Fig. ).
Pour the descaling solution into the water tank.
Place a container under the ¿lter holder seat, which shall be larger enough to collect the water of the tank.
Place the steam/hot water wand into the container.
The descaling process begins and the solution into the tank starts running through the ¿lter holder seat and through the steam/hot water wand.
Limescale deposits will thus be removed from the internal circuit of the appliance.
After several washing cycles and breaks, the descaling process is over.
Remove the water tank and rinse it with fresh water.
Fill the water tank with fresh water up to the MAX level (Fig. ).
Steam wand cleaning Warning!
The procedure must be carried out when the steam/hot water wand has cooled down to avoid burns.
Start the “Steam wand cleaning” from the display and follow the instructions given on the display.
Remove the nozzle from the steam/hot water wand (Fig. ) and rinse it under running water.
You can clean the steam/hot water wand using a non-abrasive cloth.
If needed, clean the hole of the nozzle by using the provided needle (Fig. 6).
Fasten the steam nozzle until it is locked in place.
After each use, distribute steam for a few seconds so as to clean the hole from any residue.
EN
Water hardness
Dip the water hardness test strip into cold water for one second.
Pull out the strip.
Remove the e[cess water drops.
Wait for about seconds for the result.
Select on the display the closest match to your test strip result.
&OHDQLQJRIFRPSRQHQWV
Wash the milk container (H), the ¿lter holder (G) and the ¿lters (D-E-F) in soapy water.
Rinse and dry all parts thoroughly.
&OHDQLQJWKHÀOWHUKROGHUVHDW
If the appliance is used daily, it may occur that in the ¿lter holder seat there is a sedimentation of coffee grounds. Remove any residue using a toothpick, a sponge or letting water run through the seat without install-ing the ¿lter holder (Fig. -).
Warning!
The ¿lter holder is not dishwasher-safe.
Tank cleaning Warning!
Cleaning must be carried out with the appliance switched off and with the plug disconnected from the outlet.
Regularly clean the inside of the water tank by using a sponge or a damp cloth.
&OHDQLQJRIWKHFXSUHVWLQJJULOO 2 DQGRIWKHGULSWUD\ 0 Warning!
Cleaning must be carried out with the appliance switched off and with the plug disconnected from the outlet.
Occasionally empty the drip tray (M).
The drip tray is provided with a Àoat (1). When the Àoat is visible from the cup-resting grill, the drip tray is full of water and needs to be emptied.
Remove the cup resting grill (O).
Pull off the drip tray from the appliance. Empty and wash the drip tray under running water.
Follow the same procedure to clean the cup-resting grill as well.
EN
&OHDQLQJWKHDSSOLDQFHERG\
Warning!
This cleaning operation must be carried out when the appliance’s hot parts have cooled down to room temperature.
Warning!
Do not use abrasive detergents.
Clean the ¿[ed parts of the appliance using a non-abrasive damp cloth to prevent damaging the body.
Unlocking the coffee grinder
In the event the coffee grinder gets blocked, this might be due to impurities among coffee beans which have caused the grinder to get blocked.
The mills of the grinder are completely removable. To remove the mills, proceed as follows.
Turn off the appliance.
Unplug it from the electric outlet.
Remove residual coffee powder from the ¿lter holder (G).
Turn the bezel for adjusting the grinding level (P) to the left ( ) in order to select the coarsest grinding level (9, , ) (Fig. ). Impurities having caused the appliance to block will thus fall into the compartment for coffee powder.
Remove the lid from the coffee beans container.
Turn the grinder protection to the symbol ( ).
Pull out the protection with the mills (Fig. 9-3).
Clean the grinder mills and the coffee grinder seat using the provided brush for the grinder mills cleaning (S).
Warning!
Do not wash the mills under running tap water or in the dishwasher.
Insert the mills together with the protection into its seat and lock it again turning it towards the symbol ( ).
If the mills are not inserted properly in the coffee grinder seat, an error message will appear on the display.
Plug the appliance into the outlet (Fig. ).
Press the on/off button ( ) to turn O1 the appliance (Fig. 3).
Restore the proper grinding level (see paragraph “Adjusting the grinding level”).
Place a container under the coffee grinder.
From the beverage selection home page, select a coffee beverage.
Press the coffee bean button and start the grinding (for detailed information, see paragraphs “How to make coffee beverages” and “How to distribute coffee for coffee and milk-based beverages”).
Let ground coffee fall into the container.
Throw away the ground coffee to remove impurities.
The coffee grinder is unlocked and the appliance is ready to make new beverages.